Equipment

HUM CRUSHER

CRUSHER Single Stage * Double Stage **
Type KS 313 KS 410 KS 416 KD 313 KD 410 KD 416
Capacity (Ton/24 hours) 350 400 600 350 400 600
Roll Quantity 2 2 2 2 x 2 2 x 2 2 x 2
Roll Dimensions (mm) 300 x 1300 400 x 1000 400 x 1600 300 x 1300 400 x 1000 400 x 1600
Main Motor Power (kW) 22 22 30 2 x 22 2 x 22 2 x 30

* Recommended for Soybean Warm Dehulling Process (HWDP); soybean will go through this crusher twice.
** Recommended for Soybean Cold Dehulling Process (HCDP)

HUM Crusher KD313 300x1300

The HUM CRUSHER, a product of advanced technology;

  • Has ease of use and maximum safety
  • Has long lifetime with low operational cost
  • Has lower maintenance and maintenance cost
  • The rollers in HUM crushers could be removed and assembled in one direction therefore the machines can be installed beside walls and because motors are on the machine, space is saved in the plant.
  • Electric consumption is very low when compared with its competitors.
  • Machines are fabricated from strong steel plates and profiles. Because their construction is rigid, the machine carries its weight in the safest manner. The load and the vibration of rollers during operation are absorbed properly.
  • There are leading plates ensuring entry of seed between rollers and there are side plates preventing escape of seed to shaft bearings.
  • There are plates leading the crushed seed to exit.
  • Surfaces of rollers are hardened thus high strength is attained. Bodies are ductile, firm and shock absorbing so the best conditions are ensured.
  • Amount of the material fed to the rollers is adjusted by level control mechanism.
  • When a large piece enters between feeder rollers the switch controllers warn the valves and the scraper roller permits passage of the piece between bottom and top limits that will be pre-defined.
  • Two screws operating in reverse directions in the feeding bunker where the seeds are fed to the rollers ensure continuous circulation of seeds and prevent jamming. Also it provides feeding of seeds along the entire roller.
  • With the help of chain stretching mechanism, gears of the feeding spirals and the feeding roller are perfectly engaged and motor power is used in the most efficient way on both shafts.
  • Scrapers guarantee that roller surfaces are kept perfectly clean during operation.
  • Rollers are thread cut. Thus the moving roller operates full parallel to the fixed roller. Life time of bearing is increased and homogenous product is produced.
  • Roller bearings of the rollers have long life time and mounted on synthetic materials with anti-abrasive property. Bearings allow single direction thermal elongation and shrinkage.
  • Inspection and maintenance of the machines could be performed fast and safely through the easily opening lids. Product sample could be easily taken through a special window at bottom and front.
  • The desired capacity and productivity can be attained with our machines of the advanced technology only.

These are the properties that make HUM CRUSHING exclusive.

HUM FLAKER

FLAKER
Type FS 613 FS 816 FS 821
Capacity (Ton/24hrs) * 200 350 500
Roll Dimensions (mm) 600 x 1300 800 x 1600 800 x 2100
Main Motor Power (kW) 2 x 37,5 2 x 55 2 x 75

* Capacities are based on soybean with 0.30 mm flake thickness, and may differ with cracking process quality.

The HUM ROLLER, a product of advanced technology;

HUM Flaker FS821 800x2100
  • Has ease of use and maximum safety
  • Has long lifetime with low operational cost
  • Has lower maintenance and maintenance cost
  • The rollers in HUM rollers could be removed and assembled in one direction therefore the machines can be installed beside walls and because motors are on the machine, space is saved in the plant.
  • 2 motors are used at the machines thus efficiency was improved.
  • Electric consumption is very low when compared with its competitors
  • Machines are fabricated from strong steel plates and profiles. Because their construction is rigid, the machine carries its weight in the safest manner. The load and the vibration of rollers during operation are absorbed properly.
  • There are leading plates ensuring entry of seed between rollers and there are side plates preventing escape of seed to shaft bearings.
  • There are plates leading the flaked seed to exit.
  • Surfaces of rollers are hardened thus high strength is attained. Bodies are ductile, firm and shock absorbing so the best conditions are ensured.
  • Distance between rollers are hydraulically adjusted and it is available on both bearings
  • There is a safe hydraulic unit, comprised of one-way hydraulic piston and valves for the passage of a large piece without giving any damage. The hydraulic unit does not carry the entire load for the sake of having longer lifetime. There is also a mechanical device in the unit as security.
  • Amount of the material fed between rollers is adjusted by level controller. In case of insufficient feeding, distance between the rollers is increased automatically via level controller in order to prevent contact of rollers to each other dangerously.
  • When a large piece enters between feeder rollers the switch controllers warn the valves and the scraper roller permits passage of the piece between bottom and top limits that will be pre-defined.
  • Two screws operating in reverse directions in the feeding bunker where the seeds are fed to the rollers ensure continuous circulation of seeds and prevent jamming. Also it provides feeding of seeds along the entire roller.
  • With the help of chain stretching mechanism, gears of the feeding spirals and the feeding roller are perfectly engaged and motor power is used in the most efficient way on both shafts.
  • Scrapers guarantee that roller surfaces are kept perfectly clean during operation.
  • Rollers are thread cut. Thus the moving roller operates full parallel to the fixed roller. Life time of bearing is increased and homogenous flake is produced.
  • Roller bearings of the rollers have long life time and mounted on synthetic materials with anti-abrasive property. Bearings allow single direction thermal elongation and shrinkage.
  • Rollers revolve at equal speed and thus less power is consumed by less heat and less vibration, lifetime of the machine parts are increased and maintenance is reduced.
  • Inspection and maintenance of the machines could be performed fast and safely through the easily opening lids. Product sample could be easily taken through a special window at bottom and front.
  • The desired capacity and productivity can be attained with our machines of the advanced technology only.

These are the properties that make HUM ROLLER exclusive.

HUM OIL SCREW PRESS

OIL SCREW PRESS Full Press Pre-Press
Type NYP 15F NYP 30F NYP 60F NYP 15 NYP 30 NYP 60
Capacity (ton/day) Sunflower, Canola 25-35 50-60 90-100 130-150 250-300 500-600
Soy, Cottonseed 50-60 90-100 160-170
Oil content in cake (%) 5-8 5-8 5-8 17-20 17-20 17-20
Main motor power (kW) 75 160 315 110 250 500
Overall Dimensions:            
- Length (mm) 4900 5200 7200 4900 5200 7200
- Width (mm) 900 1000 1200 900 1000 1200
- Height (mm) 1600 1600 1700 1600 1600 1700
- Inlet height (mm) 2050 2050 2250 2050 2050 2250
Weight:            
Excluding main motor (kg) 10.850 13.050 26.200 10.850 13.050 26.200
HUM Press NYP60

THE DISTINGUISHING PROPERTIES OF HUM OIL SCREW PRESSES

  • PLANETARY REDUCER, the planet reducer with silent operation, ensuring eternal life and high productivity, with low oil consumption, operating with cooled oil circulation by oil cooler; press and cooker reducers are planetary reducers in compact volume, which guarantee the most efficient, the most silent and vibration-free operation. With the reducers, which are the most critical element of power transmission system, productivity is improved by maintenance and failure free eternal life. Reducers are flange coupled to the press body and provide direct power transmission. It is a reducer of the most advanced technology, resistant to extreme conditions.
  • WORM AND COLLAR, Worms made of special alloy, strengthened by means of heat treatment or customs manufactured with armor as an alternative;
    Worms are designed to get the highest yield from the press. They are made of the materials with the longest life time, and subjected to special treatment. Surfaces have high hardness values thus optimum life is ensured.
  • FREQUENCY CONTROLLED FEEDING SCREW, The feeding screw of which revolution is frequency controlled, ensuring maximum feeding depending on the property of the material; revolution of the feeding screw is adjusted frequency controlled and thus maximum capacity operation of the press is ensured. Feeding screw is driven by a reducer motor.
  • THE MAIN SHAFT The shaft, which is cooled by permanent water circulation, ensures the best productivity. The main shaft of the press is equipped with a cooling system with stainless steel piping and special packing to ensure permanent cold water circulation.
  • HYDRAULIC CAGE OPENER, when cage is to be opened and closed, it opens and closes the cages very easily with the help of a strong telescopic piston and electric hydraulic power unit without feeling any difficulty and spending much time.